Lighting Connection

Electrician

Have your new light fittings wired in neatly and safely

Εύρος τιμής:100 € – 500 €

New lights look simple in the box. Getting them up is where people get stuck: cable ends that don't match the instructions, no earth at the old ceiling point, or an LED strip whose driver has to go somewhere. A local electrician can connect ceiling lights, wall lamps, strips and garden fittings in one visit. List every fitting when you book on FixNow, with a photo of each.

  • Ceiling and wall light connection
  • Outdoor and garden light wiring
  • LED strip and driver installation
  • Dimmer and smart switch compatibility
  • Earthing of metal fittings checked
  • New lighting points where needed

Συνδεθείτε για κράτηση

Δεν έχετε λογαριασμό;

Σχετικά με την υπηρεσία

What's usually behind the old fitting

Take down an old light in a Cypriot flat and you'll often find two or three cable ends coming straight out of the concrete ceiling, joined with a plastic connector block. Older installations may use red and black wires instead of brown and blue, and some have no earth wire at all. None of that stops the new light going up, but the electrician needs to work out which wire is which, and a metal fitting with no earth is a problem worth fixing while they're there.

They'll switch off at the board, check the point is dead, then connect the new fitting with proper terminals rather than twisted wire and tape. Then they fix it to the ceiling, put the bulbs in and test it from every switch that controls it.

Fittings that need more than three wires

  • Ceiling fans with a light: ideally the fan and light get separate control, which may mean an extra wire from the switch.
  • LED strips: the driver (the small power box) has to sit somewhere you can get at later and where it can breathe. Burying it in plaster or a sealed cabinet shortens its life.
  • Motion-sensor outdoor lights: these need power all the time, so a wall switch in front of them can cause confusion.
  • Smart or remote-control fittings: some need the wall switch left on permanently to work.

Getting the fittings ready

Unpack everything before the visit and check nothing is missing, especially small fixing screws and canopy parts. Have the bulbs ready if they're not included. Know which switch controls which point, and if you're putting a fitting somewhere there's no point yet, say so in the booking, as that's a new cable run rather than a swap. Clear furniture from under each light so a ladder can stand flat.

Γιατί να επιλέξετε αυτή την υπηρεσία

Advice before you buy

Share product photos or specifications in the chat and electricians can flag compatibility issues with dimmers, drivers or switches before you spend money on fittings.

Indoor and outdoor

From a single bedroom pendant to a terrace full of wall lights, you can post one job covering every fitting and compare complete offers.

Weatherproof outdoor connections

Ask electricians how they will seal outdoor connections against rain, humidity and coastal salt air so garden lighting keeps working through the seasons.

Checked before payment

Payment stays held by FixNow until you confirm every fitting works as it should, so flickering or dead lights get sorted first.

Συχνές ερωτήσεις

Why do my new LED lights flicker on the dimmer?
Many older dimmers were designed for traditional bulbs and do not work well with the low load of LEDs. The fix is usually a dimmer suited to LED loads, or lamps marked as dimmable. An electrician can check what you have and recommend a compatible combination when connecting your new fittings.
Can I connect a heavier or larger fitting to an existing light point?
Electrically it is usually fine, but the fixing matters. A large fitting may need a stronger anchor into the concrete ceiling than the old one. Mention the weight and size of the fitting when you post your job so electricians can plan suitable fixings or suggest a separate hanging service.
Do outdoor lights need special wiring?
Outdoor lights need fittings with an appropriate IP rating, weatherproof cable entries and connections protected from water. Circuits supplying outdoor lighting should have suitable RCD protection. In coastal areas, corrosion-resistant fixings help too. A qualified electrician can advise on the right approach for terraces, gardens and pool areas.
How long does it take to connect several light fittings?
Replacing a straightforward fitting on an existing point is generally quick, so a handful can often be done in a few hours. New cable runs, high ceilings, LED drivers or smart controls add time. Listing every fitting in your job post helps electricians give an accurate estimate in their offers.
Υπηρεσίες